26 Haziran 2015 Cuma

Cisco 2900 Serisi ISR için Şifre Kurtarma Prosedürü

Giriş


Bu belge enable password ve enable secret şifrelerini kurtarmayı açıklamaktadır. Bu şifreler ayrıcalıklı yönetim ve yapılandırma modlarına erişimi korur. enable password şifresi telafi edilebilir, ancak enable secret şifresi kriptoludur ve yeni bir şifre ile değiştirilmelidir. Enable secret şifresini değiştirmek için bu belgede açıklanan prosedürü kullanın.


Önkoşullar


Gereksinimler


Bu belge için herhangi bir özel gereksinim yoktur.


Kullanılan Bileşenler


Bu belgede yer alan bilgiler, bu donanım versiyonlarına dayanmaktadır:
  • Cisco 2900 Serisi Entegre Servis Router (ISR)

Bu belgede yer alan bilgiler, belirli bir laboratuar ortamında cihazlardan oluşturuldu. Bu belgede kullanılan cihazların tümü temizlenmiş (varsayılan) yapılandırma ile başladı. Ağınız canlı ise, herhangi bir komutun potansiyel etkilerini anladığınızdan emin olun.


Adım Adım Prosedür


Şifrenizi kurtarmak için aşağıdaki adımları uygulayınız:
  1. Routerı ya kapatın veya güç kablosunu çekiniz.
  2. Routerın arkasındaki kompakt flaşı çıkarın. Bu görüntü 2951 routerın arkasını gösterir:
    C2900-şifre kurtarma-01.gif
  3. Routerı çalıştırınız.
  4. Router ROMMON modunda açıldığı zaman, kompakt flaşı takınız.
  5. Flaşın önyüklemesi için ROMMON 1> isteminde confreg 0x2142. yazınız.
    Bu adım şifrelerin saklandığı başlangıç ​​yapılandırmasını(startup-configuration) atlar. Burada dikkat edilmesi gereken bir diğer hususta 0x2142 yazarken çarpma işareti (*) değil harf olan (x) kullanılmasıdır. 
  6. ROMMON 2> isteminde reset yazınız.
    Router yeniden başlar, ancak kaydedilmiş yapılandırmayı yok sayar.
  7. Her kurulum sorusuna hayır yazınız veya ilk kurulum prosedürünü atlamak için Ctrl-C tuşlarına basınız.
  8. Router> isteminde enable yazınız.
    "Enable mod"da olduğunuzu ve Router# istemini görmelisiniz.
  9. Geçici olmayan RAM'ı (NVRAM) belleğe kopyalamak için configure memory veya copy startup-config running-config yazınız.
    Uyarı: copy running-config startup-config veya write komutlarını girmeyiniz. Bu komutlar sizin başlangıç ​​yapılandırmanızı(startup-config) silebilir.
  10. show running-config komutunu uygulayınız.
    show running-config komutu router yapılandırmasını gösterir. Bu yapılandırmada, tüm arabirimlerin(interfaces) altında gördüğünüz shutdown komutu arabirimlerin halen kapalı olduğunu gösterir. Buna ek olarak, ister kriptolu olsun ister kriptosuz, şifreleri (enable password, enable secret, vty, ve konsol şifrelerini) görebilirsiniz. Kriptosuz şifreleri yeniden kullanabilirsiniz. Kriptolu şifreleri yeni şifreler ile değiştirmeniz gerekir.
  11. configure terminal yazınız.
    hostname(config)# istemi görüntülenir.
  12. enable secret değiştirmek için enable secret <yeni şifre> yazınız. Örneğin:
    hostname(config)#enable secret cisco
    
  13. Kullandığınız her arabirimde no shutdown komutunu uygulayınız.
    show ip interface brief komutunu uygularsanız, kullanmak istediğiniz bütün arayüzlerin up upolarak göreceksiniz.
  14. config-register <configuration_register_setting> yazınız. Burada<configuration_register_setting> ya 2. adımda girdiğiniz değerdir ya da 0x2102. Örneğin:
    hostname(config) #config-register 0x2102
    
  15. Yapılandırma modundan çıkmak için Ctrl-z basınız veya end yazınız.
    hostname# istemi görüntülenir.
  16. Değişiklikleri işlemek amacıyla write memory veya copy running-config startup-configyazınız.

Şifre Kurtarma Prosedürü Örneği


Bu bölümde şifre kurtarma işleminin bir örnek göreceğiz. Bu örnek, bir Cisco 2900 serisi ISR ​​ile oluşturuldu. Bir Cisco 2900 Serisi ISR ​​kullanmasanız bile, bu çıktı da ürün üzerinde deneyim edinmenizi sağlayan bir örnek.

Router>
enable

Password:
Password:
Password:
% Bad secrets

Router>
show version

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, 
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Technology Package License Information for Module:'c2900'

----------------------------------------------------------------
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
-----------------------------------------------------------------
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
uc            uck9          Permanent     uck9
data          datak9        Permanent     datak9

Configuration register is 0x2102


Router>



!--- Execute Steps 1 through 4 from Step-by-Step Procedure.


!

rommon 1 > confreg 0x2142

You must reset or power cycle for new config to take effect

rommon 2 > reset

System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)
Copyright (c) 2009 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2900 platform with 524288 Kbytes of main memory


program load complete, entry point: 0x80008000, size: 0x6fdb4c

Self decompressing the image : ###############################
##############################################################
##############################################################
##############################################################
############################### [OK]


 Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

 cisco Systems, Inc.
 170 West Tasman Drive
 San Jose, California 95134-1706

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)


 --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

00:00:19: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, 
changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0,
 changed state to up
Router>
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, 
changed state to up
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, 
changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, 
changed state to down
00:00:50: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team
00:00:50: %LINK-5-CHANGED: Interface BRI0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Ethernet0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Serial0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Ethernet0/1, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Serial0/1, 
changed state to administratively down
00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, 
changed state to down
00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, 
changed state to down
Router>
Router>enable
Router#copy startup-config running-config
Destination filename [running-config]?
1324 bytes copied in 2.35 secs (662 bytes/sec)
Router#
00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, 
changed state to down
00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, 
changed state to down
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret < password >
Router(config)#^Z
00:01:54: %SYS-5-CONFIG_I: Configured from console by console
Router#show ip interface brief

Interface   IP-Address        OK?  Method     Status                   Protocol
Ethernet0/0 10.200.40.37      YES  TFTP       administratively down    down
Serial0/0   unassigned        YES  TFTP       administratively down    down
BRI0/0      193.251.121.157   YES  unset      administratively down    down
BRI0/0:1    unassigned        YES  unset      administratively down    down
BRI0/0:2    unassigned        YES  unset      administratively down    down
Ethernet0/1 unassigned        YES  TFTP       administratively down    down
Serial0/1   unassigned        YES  TFTP       administratively down    down
Loopback0   193.251.121.157   YES  TFTP       up                       up
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface Ethernet0/0
Router(config-if)#no shutdown
Router(config-if)#
00:02:14: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:02:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, 
changed state to up
Router(config-if)#interface BRI0/0
Router(config-if)#no shutdown
Router(config-if)#
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
00:02:115964116991: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0, 
TEI 68 changed to up
Router(config-if)#^Z
Router#
00:02:35: %SYS-5-CONFIG_I: Configured from console by console
Router#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Configuration register is 0x2102

Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#config-register 0x2102
Router(config)#^Z
00:03:20: %SYS-5-CONFIG_I: Configured from console by console

Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Configuration register is 0x2142 (will be 0x2102 at next reload)

Router#

Kaynak: Cisco
Çeviren: Aydın Güleç